# IP: 141.193.149.3
# X-Cfg-Ver: 10.10.0-RC2
# X-Envoy-Expected-Rq-Timeout-Ms: 120000
# X-Envoy-External-Address: 141.193.149.3
# X-Forwarded-For: 141.193.149.3
# X-Forwarded-Proto: https
# X-Request-Id: dc20bc0f-3d14-458b-895c-7e902ceb71af

###

# # Problem description

# # No gyro flash hobby F05

# ###

# version
# Betaflight / STM32F405 (S405) 4.5.0 Jan  9 2024 / 21:54:35 (f1cbd83f0) MSP API: 1.46
# config rev: 7982a5b
# board: manufacturer_id: FHRC, board_name: FLASHHOBBYF405

# status
MCU F40X Clock=168MHz (PLLP-HSE), Vref=3.31V, Core temp=41degC
Stack size: 2048, Stack address: 0x1000fff0
Configuration: UNCONFIGURED, size: 4158, max available: 16384
Devices detected: SPI:0, I2C:0
Gyros detected: locked

OSD: MSP (30 x 13)
BUILD KEY: d8b7632a201403bc9d2b9822c9e31ff9 (4.5.0-RC2)
System Uptime: 36 seconds, Current Time: 2024-01-09T22:02:48.605+00:00
CPU:0%, cycle time: 0, GYRO rate: 0, RX rate: 0, System rate: 9
Voltage: 494 * 0.01V (0S battery - NOT PRESENT)
I2C Errors: 1
GPS: NOT ENABLED
Arming disable flags: NOGYRO BOOTGRACE CLI MSP

# flash_info
Flash sectors=0, sectorSize=0, pagesPerSector=0, pageSize=0, totalSize=0 JEDEC ID=0x00000000
Partitions:
FlashFS size=0, usedSize=0

# dump hardware

# version
# Betaflight / STM32F405 (S405) 4.5.0 Jan  9 2024 / 21:54:35 (f1cbd83f0) MSP API: 1.46
# config rev: 7982a5b

# start the command batch
batch start

board_name FLASHHOBBYF405
manufacturer_id FHRC

# resources
resource BEEPER 1 B02
resource MOTOR 1 B00
resource MOTOR 2 B01
resource MOTOR 3 B05
resource MOTOR 4 B04
resource MOTOR 5 B06
resource MOTOR 6 B07
resource MOTOR 7 C08
resource MOTOR 8 C09
resource SERVO 1 NONE
resource SERVO 2 NONE
resource SERVO 3 NONE
resource SERVO 4 NONE
resource SERVO 5 NONE
resource SERVO 6 NONE
resource SERVO 7 NONE
resource SERVO 8 NONE
resource PPM 1 A03
resource PWM 1 NONE
resource PWM 2 NONE
resource PWM 3 NONE
resource PWM 4 NONE
resource PWM 5 NONE
resource PWM 6 NONE
resource PWM 7 NONE
resource PWM 8 NONE
resource SONAR_TRIGGER 1 NONE
resource SONAR_ECHO 1 NONE
resource LED_STRIP 1 A08
resource SERIAL_TX 1 A09
resource SERIAL_TX 2 A02
resource SERIAL_TX 3 B10
resource SERIAL_TX 4 A00
resource SERIAL_TX 5 NONE
resource SERIAL_TX 6 C06
resource SERIAL_TX 7 NONE
resource SERIAL_TX 8 NONE
resource SERIAL_TX 9 NONE
resource SERIAL_TX 10 NONE
resource SERIAL_TX 11 NONE
resource SERIAL_RX 1 A10
resource SERIAL_RX 2 A03
resource SERIAL_RX 3 B11
resource SERIAL_RX 4 A01
resource SERIAL_RX 5 D02
resource SERIAL_RX 6 C07
resource SERIAL_RX 7 NONE
resource SERIAL_RX 8 NONE
resource SERIAL_RX 9 NONE
resource SERIAL_RX 10 NONE
resource SERIAL_RX 11 NONE
resource INVERTER 1 NONE
resource INVERTER 2 NONE
resource INVERTER 3 NONE
resource INVERTER 4 NONE
resource INVERTER 5 NONE
resource INVERTER 6 NONE
resource INVERTER 7 NONE
resource INVERTER 8 NONE
resource INVERTER 9 NONE
resource INVERTER 10 NONE
resource INVERTER 11 NONE
resource SOFTSERIAL_TX 1 NONE
resource SOFTSERIAL_TX 2 NONE
resource SOFTSERIAL_RX 1 NONE
resource SOFTSERIAL_RX 2 NONE
resource I2C_SCL 1 B08
resource I2C_SCL 2 NONE
resource I2C_SCL 3 NONE
resource I2C_SDA 1 B09
resource I2C_SDA 2 NONE
resource I2C_SDA 3 NONE
resource LED 1 C14
resource LED 2 NONE
resource LED 3 NONE
resource RX_BIND 1 NONE
resource RX_BIND_PLUG 1 NONE
resource TRANSPONDER 1 NONE
resource SPI_SCK 1 A05
resource SPI_SCK 2 B13
resource SPI_SCK 3 C10
resource SPI_SDI 1 A06
resource SPI_SDI 2 B14
resource SPI_SDI 3 C11
resource SPI_SDO 1 A07
resource SPI_SDO 2 B15
resource SPI_SDO 3 C12
resource ESCSERIAL 1 D02
resource CAMERA_CONTROL 1 B03
resource ADC_BATT 1 C02
resource ADC_RSSI 1 NONE
resource ADC_CURR 1 C01
resource ADC_EXT 1 NONE
resource BARO_CS 1 NONE
resource BARO_EOC 1 NONE
resource BARO_XCLR 1 NONE
resource PINIO 1 C13
resource PINIO 2 NONE
resource PINIO 3 NONE
resource PINIO 4 NONE
resource USB_MSC_PIN 1 NONE
resource FLASH_CS 1 A15
resource OSD_CS 1 B12
resource GYRO_EXTI 1 C04
resource GYRO_EXTI 2 NONE
resource GYRO_CS 1 A04
resource GYRO_CS 2 NONE
resource USB_DETECT 1 C05
resource VTX_POWER 1 NONE
resource VTX_CS 1 NONE
resource VTX_DATA 1 NONE
resource VTX_CLK 1 NONE
resource PULLUP 1 NONE
resource PULLUP 2 NONE
resource PULLUP 3 NONE
resource PULLUP 4 NONE
resource PULLDOWN 1 NONE
resource PULLDOWN 2 NONE
resource PULLDOWN 3 NONE
resource PULLDOWN 4 NONE

# timer
timer B00 AF2
# pin B00: TIM3 CH3 (AF2)
timer B01 AF2
# pin B01: TIM3 CH4 (AF2)
timer B05 AF2
# pin B05: TIM3 CH2 (AF2)
timer B04 AF2
# pin B04: TIM3 CH1 (AF2)
timer B06 AF2
# pin B06: TIM4 CH1 (AF2)
timer B07 AF2
# pin B07: TIM4 CH2 (AF2)
timer C08 AF3
# pin C08: TIM8 CH3 (AF3)
timer C09 AF3
# pin C09: TIM8 CH4 (AF3)
timer B03 AF1
# pin B03: TIM2 CH2 (AF1)
timer A03 AF2
# pin A03: TIM5 CH4 (AF2)
timer A08 AF1
# pin A08: TIM1 CH1 (AF1)

# dma
dma SPI_SDO 1 NONE
dma SPI_SDO 2 NONE
dma SPI_SDO 3 NONE
dma SPI_SDI 1 NONE
dma SPI_SDI 2 NONE
dma SPI_SDI 3 NONE
dma SPI_TX 1 NONE
dma SPI_TX 2 NONE
dma SPI_TX 3 NONE
dma SPI_RX 1 NONE
dma SPI_RX 2 NONE
dma SPI_RX 3 NONE
dma ADC 1 0
# ADC 1: DMA2 Stream 0 Channel 0
dma ADC 2 NONE
dma ADC 3 NONE
dma UART_TX 1 NONE
dma UART_TX 2 NONE
dma UART_TX 3 NONE
dma UART_TX 4 NONE
dma UART_TX 5 NONE
dma UART_TX 6 NONE
dma UART_TX 7 NONE
dma UART_TX 8 NONE
dma UART_TX 9 NONE
dma UART_TX 10 NONE
dma UART_TX 11 NONE
dma UART_RX 1 NONE
dma UART_RX 2 NONE
dma UART_RX 3 NONE
dma UART_RX 4 NONE
dma UART_RX 5 NONE
dma UART_RX 6 NONE
dma UART_RX 7 NONE
dma UART_RX 8 NONE
dma UART_RX 9 NONE
dma UART_RX 10 NONE
dma UART_RX 11 NONE
dma pin B00 0
# pin B00: DMA1 Stream 7 Channel 5
dma pin B01 0
# pin B01: DMA1 Stream 2 Channel 5
dma pin B05 0
# pin B05: DMA1 Stream 5 Channel 5
dma pin B04 0
# pin B04: DMA1 Stream 4 Channel 5
dma pin B06 0
# pin B06: DMA1 Stream 0 Channel 2
dma pin B07 0
# pin B07: DMA1 Stream 3 Channel 2
dma pin C08 1
# pin C08: DMA2 Stream 4 Channel 7
dma pin C09 0
# pin C09: DMA2 Stream 7 Channel 7
dma pin B03 0
# pin B03: DMA1 Stream 6 Channel 3
dma pin A03 1
# pin A03: DMA1 Stream 3 Channel 6
dma pin A08 1
# pin A08: DMA2 Stream 1 Channel 6

# feature
feature -RX_PPM
feature -INFLIGHT_ACC_CAL
feature -RX_SERIAL
feature -MOTOR_STOP
feature -SERVO_TILT
feature -SOFTSERIAL
feature -GPS
feature -RANGEFINDER
feature -TELEMETRY
feature -3D
feature -RX_PARALLEL_PWM
feature -RX_MSP
feature -RSSI_ADC
feature -LED_STRIP
feature -DISPLAY
feature -OSD
feature -CHANNEL_FORWARDING
feature -TRANSPONDER
feature -AIRMODE
feature -RX_SPI
feature -ESC_SENSOR
feature -ANTI_GRAVITY
feature RX_SERIAL
feature SERVO_TILT
feature RANGEFINDER
feature TELEMETRY
feature LED_STRIP
feature DISPLAY
feature OSD
feature CHANNEL_FORWARDING
feature TRANSPONDER
feature AIRMODE
feature ANTI_GRAVITY

# serial
serial 20 1 115200 57600 0 115200
serial 0 0 115200 57600 0 115200
serial 1 64 115200 57600 0 115200
serial 2 0 115200 57600 0 115200
serial 3 0 115200 57600 0 115200
serial 4 0 115200 57600 0 115200
serial 5 0 115200 57600 0 115200

# master
set gyro_to_use = FIRST
set baro_bustype = I2C
set baro_spi_device = 0
set baro_i2c_device = 1
set baro_i2c_address = 0
set adc_device = 1
set blackbox_device = SPIFLASH
set motor_kv = 1960
set dshot_burst = AUTO
set dshot_bitbang = OFF
set dshot_bitbang_timer = AUTO
set current_meter = ADC
set battery_meter = ADC
set vbat_scale = 110
set ibata_scale = 200
set beeper_inversion = ON
set beeper_od = OFF
set beeper_frequency = 0
set system_hse_mhz = 8
set vtx_spi_bus = 0
set max7456_clock = NOMINAL
set max7456_spi_bus = 2
set max7456_preinit_opu = OFF
set led_inversion = 0
set dashboard_i2c_bus = 0
set dashboard_i2c_addr = 60
set pinio_config = 1,1,1,1
set pinio_box = 40,255,255,255
set usb_msc_pin_pullup = ON
set flash_spi_bus = 3
set gyro_1_bustype = SPI
set gyro_1_spibus = 1
set gyro_1_i2cBus = 0
set gyro_1_i2c_address = 0
set gyro_1_sensor_align = CW0
set gyro_1_align_roll = 0
set gyro_1_align_pitch = 0
set gyro_1_align_yaw = 0
set gyro_2_bustype = NONE
set gyro_2_spibus = 0
set gyro_2_i2cBus = 0
set gyro_2_i2c_address = 0
set gyro_2_sensor_align = DEFAULT
set gyro_2_align_roll = 0
set gyro_2_align_pitch = 0
set gyro_2_align_yaw = 0
set i2c1_pullup = OFF
set i2c1_clockspeed_khz = 800
set i2c2_pullup = OFF
set i2c2_clockspeed_khz = 800
set i2c3_pullup = OFF
set i2c3_clockspeed_khz = 800
set mco2_on_pc9 = OFF
set scheduler_relax_rx = 25
set scheduler_relax_osd = 25
set box_user_1_name = -
set box_user_2_name = -
set box_user_3_name = -
set box_user_4_name = -

# end the command batch
batch end

#